Setting and Maintenance of Constant Temperature and Humidity Test Chamber
Constant temperature and humidity test chamber is a relatively precise test equipment. In order to ensure the smooth completion of each test process, the power supply of the connected equipment must be stable at around 380V to ensure that the compressor will not be damaged. In addition, you must ensure the personal safety of the personnel who receive the power, so please understand the specific operation methods before wiring.
Constant temperature and humidity test chamber adjust or replace the connected power supply. After checking that the voltage of the power supply to be connected is correct, connect the neutral terminal to the neutral terminal in the distribution chamber. Ensure that the neutral line is connected, otherwise it may cause the equipment of the constant temperature and humidity test chamber to fail to work normally or burn electrical components.
After confirming that the neutral wire is connected, connect the 3 ∮ wire to the three terminals under the main switch of the distribution chamber in the constant temperature and humidity test chamber, and tighten the screws. We need to connect the ground wire, which is connected in the same way as other power cables, and directly to the ground terminal of the distribution chamber. In the process of connecting each power cord, everyone must ensure that the different colors of the power cord can be correctly identified to avoid connection errors and normal testing.
Maintenance of constant temperature and humidity test chamber:
1, Clean the water circulation system: clean the water filter, replace the filter, check the operation of the pump, including the operation of the water flow switch, adjust the water circulation flow and test operation.
2, Check all electrical wiring and electrical components to ensure reliable operation and good contact.
3, Replace the fresh air filter.
4, Refrigeration system cleaning: replace the refrigeration oil, clean the oil filter.
5, Check the vulnerable parts of the refrigeration system: check the sealing condition of the compressor and connecting parts, and replace all filters.
6, Refrigeration system leakage inspection: check all the connecting parts of the refrigeration system and the connecting parts of the valve plate are leaked and tightened.
7, According to the working conditions to supplement refrigerant: check whether the need to supplement the system refrigerant to ensure effective cooling capacity.
8, Comprehensive system operation: check whether the operating components are in good condition.
Maintenance Method of High and Low Temperature Test Chamber
There are three common types of high and low temperature test chamber controllers: software failure, system failure and hardware failure.
1, Software failure:
Software failure mainly refers to the controller failure of the high and low temperature test chamber, including the internal parameters, the control point IS control and output signal of the solenoid valve on and off.
2, System failure:
System failure refers to the initial design problems of the refrigeration system, including the leakage of refrigerant caused by high and low temperature test chamber does not cool down, and refrigerant leakage is often due to transport and high and low temperature test chamber operation jitter or refrigeration copper pipe welding process is not fine and other reasons caused.
3, Hardware failure:
Hardware failure may lead to non-cooling hardware compressor, solenoid valve and other refrigeration components.
Then the user can listen and touch to roughly understand what is the hardware high and low temperature test chamber damage, if it is a compressor failure, the compressor sound will be abnormal or do not work does not start or the compressor itself temperature is much higher than usual temperature, and the solenoid valve failure and other refrigeration components failure users are not too good to master.
In addition, the damage of the controller and the damage of the electronic parts of the control refrigeration system may also cause the phenomenon of non-cooling and non-cooling of the high and low temperature test chamber.
Scientific principle of heating and cooling of high and low temperature test chamber:
The high and low temperature test chamber has the functions of heating, cooling, humidification and dehumidification, and can detect the product's high temperature resistance, low temperature resistance and humidity resistance. How is the temperature in the high and low temperature test chamber controlled?
The heating device is the key link to control whether the high and low temperature test chamber is heated up. The controller outputs voltage to the relay when it gets the heating instruction. The high and low temperature test chamber is about 3-12 volts of direct current added to the solid state relay. The AC end of the high and low temperature test chamber is equivalent to a wire connection, and the contactor is also drawn at the same time. Heat up the constant temperature and humidity test chamber.
Cooling is an important part of the high and low temperature test chamber, which directly affects the determination of a high and low temperature and performance, including compressor, condenser, throttling device, evaporator four major components, compressor is the heart of the refrigeration system, it inhales low temperature and low pressure gas, into high temperature and high pressure gas, through condensation into a liquid to release heat, through the fan to take away heat, Therefore, the test chamber is the reason of hot air, and then become low pressure liquid through throttling, and then become low temperature and low pressure gas through the evaporator back to the compressor, the refrigerant in the evaporator to absorb the heat of the high and low temperature chamber to complete the gasification process and absorb heat, to achieve the purpose of refrigeration, to complete the high and low temperature test chamber cooling process.
High and low temperature chamber temperature and cooling rate test procedure:
In the adjustable range of the temperature of the test chamber, the lowest nominal temperature was selected as the lowest cooling temperature, and the highest nominal temperature was selected as the highest heating temperature.
Open the cold source, so that the test chamber from room temperature to the lowest cooling temperature, stable for at least 3 hours, rise to the highest heating temperature, stable for at least 3 hours and then to the lowest cooling temperature, during the heating and cooling, record once a minute, until the end of the test process.
The principle of high and low temperature test chamber heating and cooling is so, the realization of its function is completed by the setting of the control system, understanding the principle of heating and cooling, in the use of high and low temperature test chamber must be more handy.
Composition of Electrical Components of High and Low Temperature Test Chamber
The main parts of high and low temperature test chamber are refrigeration units, condensers, evaporators, and controllers. The main parts play a key role, so everyone pays special attention to its main parts raw materials. However, most of them ignore its auxiliary parts at this time, or feel that the role of auxiliary parts is not worth noting. Few people want to count the specific parts, so it is not clear what specific electronic components are fully used in the constant temperature and humidity test chamber.
1, Refrigeration unit:
Used to control the operation of refrigeration unit, to carry out refrigeration cycle, and there are single-phase and three-phase.
2, Fan motor:
Used to control the fan circulation steam body, heat exchanger heat conduction, and there are indoor and outdoor.
3, Electric heater equipment:
Used for heating indoor air quality quality, tubular, flocculent points.
4, Timer:
Used for automatic control system timing boot.
5, DC contactor:
Used for refrigeration unit motor breaking and connection.
6, Leakage protector power switch:
It can not only connect or disconnect the main circuit like other switches, with the effect of leakage current detection and discrimination, when the main control circuit caused by power outage or cable sheath damage, leakage protection switch power supply main switch can be connected or disconnected switch components according to the identification results. It can be combined with isolation switch and heat relay to form a full-function low-voltage switching electronic device.
7, Overtemperature protection equipment:
Its role can not be ignored, when the controller temperature is not sensitive, the implementation of the E double maintenance of the box overtemperature, when the alarm is caused, the maintenance standby, the alarm will be different with the test temperature, relative change, you can further have the role of overtemperature maintenance. The basic concept is that when the total current flow of the broken wire exceeds the limit value, the temperature of the broken wire rises and the broken wire is broken. When the heat value caused by the broken wire does not exceed its short circuit capacity, the balance between the heat value and the released heat value is guaranteed, the temperature of the broken wire cannot reach the melting temperature, it is not easy to break.
Like this kind of small electronic components, in the high and low temperature test chamber looks innocuous, but for the structure of a test chamber is also very useful, without these components, a test chamber is not used, in short, the details determine the success of failure, fine without size, in the grasp of the test chamber at the same time, more should be from its key links to grasp.
Lighting Installation Position of High and Low Temperature Test Chamber
According to the different needs of users, the installation position of the lamp in the high and low temperature laboratory is different. The constant temperature and humidity test chamber tests the heat resistance, cold resistance, dry resistance and moisture resistance of various materials. Suitable for electronic, electrical, food, vehicle, metal, chemical, building materials and other industries of quality control. This series of products is suitable for aerospace products, information electronic instruments, materials, electrical, electronic products, various electronic components in high and low temperature or temperature and humidity environment, to test its various performance indicators.
The most common temperature test equipment in environmental test equipment, and similar related products are high and low temperature alternating test chamber, constant temperature and humidity test chamber, high and low temperature and humidity alternating test chamber and so on. It is suitable for high temperature and low temperature reliability test of industrial products. Walk-in high and low temperature test chamber, walk-in high and low temperature test chamber is used for thermal test of national defense industry, aerospace industry, automatic components, automotive parts, electronic and electrical parts, plastics, chemical, pharmaceutical industry and related products. It provides large parts, semi-finished products, and large temperature and humidity test environment space for finished products. It is suitable for the test equipment with large quantity and volume.
Some are installed on the interal chamber or door, and some are not installed. Where is the best place to install light bulbs?
In fact, the high and low temperature test chamber lighting has advantages and disadvantages no matter where it is installed.
If the lighting is installed in the broadcast room, you can clearly see the condition of the entire broadcast room and observe the product at any time.
The lamp is installed on the door, and when the user conducts the double 85 test or the high temperature and high humidity test, the humidity is not easy to invade the lamp, and the lamp is not easy to damage, which can greatly reduce the after-sales service fee. However, its observation field is very small, can only observe the near attractions, customers observe the product is not very convenient.
If the lamp is installed on the right side of the internal chamber, it is recommended to be completely sealed to prevent moisture intrusion to ensure the long-term stable operation of the lamp. If it is installed on a door, it is recommended that the viewing window be trapezoid, so that you can have a wider field of view.
Of course, some corporate customers choose not to install lighting when purchasing high and low temperature test chambers to reduce production costs and later management costs. However, customers can not observe products at any time when doing tests, and they can not meet the needs of different customers who want to observe products.
Sealing Problems and Solutions of High and Low Temperature Test Chamber
High and low temperature test chamber is based on the natural environment such as high temperature, ultra-low temperature, high and low temperature and low temperature drying in the room during the construction of work, and then carries out high and low temperature test and temperature and humidity aging resistance experiment on the commodity, mainly used for industrial products, such as: electronic and electrical, instrumentation equipment, cars and motorcycles, universities and other manufacturing industries.
Because of high temperature testing, ultra-low temperature testing, high and low temperature test cycle system testing, high and low temperature test and other experimental standards, high and low temperature test chamber in the high temperature standards, such as doing 150 ° C extremity of high temperature and 98% of the ambient humidity conditions, and the pressure difference between inside and outside the laboratory to expand substantially, at this moment, the sealing effect of the test chamber really matters. If the airtightness is not very good, it will cause more serious vapor leakage, affecting the precision and accuracy of the temperature.
What are the factors that cause the sealing problem of the high and low temperature test chamber?
First, the constant temperature and humidity test chamber usually has cable holes and ventilation exhaust holes, and the design scheme is very strict.
If the design scheme and production are not scientific, the gap will be too large, and the sealing of the environmental test chamber will not be good. This punching studio should also remember to plug the suitable specifications of the bottle stopper, rubber stopper, etc., to ensure that the sealing of this punching place is intact.
Second, the problem of sealing rubber strips of high and low temperature test chamber. We usually ignore this problem, feel that the sealing strip is added to the door hinge, and should be very sealable under the inhibition of the door hinge, because the aging of the silicone seal, the selection of hard flexibility is unscientific, and the sealing strip is fixed and not the same, often causing steam leakage. It is also simple to handle, often test its tightness, and find that the embrittlement of the sealing strip must be replaced as soon as possible.
Third, because the general volume of the high and low temperature test chamber is relatively large, the tail door specifications are expanded, and the net weight is very large, and the vertical orientation of the door hinge is offset after the long-term load, and the tail door is shifted and closed. Such problems are usually dealt with according to the modified high-load door hinges and the total number of door hinges.
From the above analysis, it can be seen that the sealing problem of the high and low temperature test chamber has some design problems and some maintenance problems. Therefore, we should strictly follow the equipment maintenance manual for regular maintenance in the use of equipment to ensure the normal operation of equipment and no deviation of technical parameters.
Principles That Operating Constant Temperature and Humidity Test Chamber Should Follow
Constant temperature and humidity test chamber, also known as constant temperature and humidity test machine, programmable temperature and humidity alternating test chamber, thermostat or constant temperature and humidity chamber, can be used to test various environments and test equipment material performance, this material has heat resistance, cold resistance, dry resistance and humidity resistance. However, when using the constant temperature and humidity test chamber, the correct operation helps to obtain scientific data for the experimenter, so what principles should be followed in the operation of the constant temperature and humidity test chamber?
First, in the environmental test, the operator must be familiar with the required test sample performance, test conditions, test procedures and test technology, familiar with the technical performance of the test equipment used, and understand the structure of the equipment, especially familiar with the control operation and performance. At the same time, read the operation manual of the test equipment carefully to avoid abnormal operation of the test equipment due to operation errors, which may cause damage to the test sample and incorrect test data.
Second, in order to ensure the normal operation of the test, appropriate testing equipment should be selected according to the different conditions of the test sample, and a reasonable proportion between the temperature and humidity of the test sample and the effective volume of the laboratory should be maintained. For tests of heated test samples, the volume should not be greater than one-tenth of the effective volume of the test chamber. The volume of the unheated test sample should not exceed one-fifth of the effective volume of the test chamber.
Third, for environmental tests that need to add media to the test, it should be correctly added according to the test requirements. For example, there are certain requirements for water in temperature and humidity test chambers and the resistance should be reduced. There is a more economical and convenient form of pure water on the market. Its resistance is equivalent to distilled water.
Fourth, wet bulb gauze (wet bulb paper) has certain requirements for use in a temperature and humidity test chamber, and no gauze can be replaced, because the relative humidity reading is the difference between the root distance and temperature and humidity, and strictly speaking, it is also related to the local atmospheric pressure and wind speed at the time. The indicator value of wet-bulb temperature is related to the amount of water absorbed by the gauze and the amount of surface evaporation. These are directly related to the quality of the gauze, so the weather stipulates that the wet ball gauze must be a special "wet ball gauze" woven from linen. Otherwise, it is difficult to ensure the correctness of the wet bulb thermometer value, that is, the correctness of the humidity. In addition, the position of the wet gauze is also clearly specified. Gauze length: 100mm, tightly wrap the sensor probe, probe 25-30mm away from the humidity cup, gauze immersed in the cup to ensure the accuracy of equipment control and humidity.
Fifth, the location of the test sample should be more than 10 cm away from the wall of the chamber, and multiple samples should be placed on the same plane as far as possible. Samples should be placed without blocking air outlets and return vents, and temperature and humidity sensors should be kept at a distance. Make sure the test temperature is correct.
Operating the constant temperature and humidity test chamber in accordance with the above principles, the correct operation of the test process will greatly improve the level of test data. As long as the above principles are adhered to, it should be said that the temperature and humidity tests can be successfully performed.
Introduction and Comparison of Thermocouple Temperature Sensing Lines
Instructions:
The background principle of thermocouple is "seebeck effect", also known as the thermoelectric effect, the phenomenon is that when two different metal endpoints are connected to form a closed loop, and if there is a temperature difference between the two endpoints, then there will be current generated between the loops, and the higher temperature contact in the loop is called "hot junction". This point is usually placed at the temperature measurement; The lower end of the temperature is called "cold junction", that is, the output end of the thermocouple, whose output signal is: DC voltage is converted into a digital signal through the A/D converter and converted into the actual temperature value through the softwares algorithm.
Various electric heating couples and their range of use(ASTM E 230 T/C):
type E
type J
type K
-100℃ to 1000℃±0.5℃
0℃ to 760℃±0.1℃
0℃ to 1370℃±0.7℃
Brown (skin color)+ purple - red
Brown (skin color)+ white - red
Brown (skin color)+ yellow - red
JIS,ANSI(ASTM) thermoelectric coupling appearance identification:
Thermoelectric coupling
JIS
ANSI(ASTM)
Rind
Positive end
Negative end
Rind
Positive end
Negative end
B type
Grayish
Red
white
Grayish
Grayish
Red
R,S type
Brown
Red
white
Green
Brown
Red
K,W,V type
Green
Red
white
Yellow
Yellow
Red
E type
Purple
Red
white
Purple
Purple
Red
J type
Yellow
Red
white
Brown
white
Red
T type
Tawny
Red
white
Green
Green
Red
Note:
1.ASTM, ANSI: American standard
2.JIS: Japanese standard
High and Low Temperature Test Standard for PC Plastic Material
First, high temperature test
After being placed at 80±2°C for 4 hours and at normal temperature for 2 hours, the dimensions, insulation resistance, voltage resistance, key function, and loop resistance should meet normal requirements, and the appearance should not be deformed, warped, or degumming. Key bumps collapsing at high temperatures and reduced pressing force are not evaluated.
Second, low temperature test
After being placed at -30±2℃ for 4 hours and at normal temperature for 2 hours, the dimensions, insulation resistance, voltage resistance, key function, and loop resistance should meet normal requirements, and the appearance should not be deformed, warped, or degumming.
Third, temperature cycling test
After being placed in 70±2℃ for 30 minutes, remove at room temperature for 5 minutes; then after being placed in -20±2℃ for 30 minutes, remove at room temperature for 5 minutes. After such 5 cycles, the dimensions, insulation resistance, voltage resistance, key function, and loop resistance should meet normal requirements, and the appearance should not be deformed, warped, or degumming. Key bumps collapsing at high temperatures and reduced pressing force are not evaluated.
Fourth, heat resistance
After being placed in an environment with a temperature of 40±2℃ and a relative humidity of 93±2%RH for 48 hours, the dimensions, insulation resistance, voltage resistance, key function, and loop resistance should meet normal requirements, and the appearance should not be deformed, warped, or degumming. Key bumps collapsing at high temperatures and reduced pressing force are not evaluated.
Composition and Application of Temperature and Humidity Regulating Chamber
Temperature and humidity regulating chamber is a device that controls the ambient temperature and humidity. It can provide a stable temperature and humidity environment to meet the requirements of a specific product or experiment. Temperature and humidity regulating chamber is usually composed of a control system, a heating system, a cooling system, a humidity control system and a circulation system.
In terms of working principle, temperature and humidity regulating chamber realizes temperature control through the control system to control the operation of the heating system and the refrigeration system. When the temperature is too low, the heating system starts and provides heat to raise the temperature; When the temperature is too high, the refrigeration system starts and absorbs heat to reduce the temperature. In this way, the temperature regulator can maintain a stable operating temperature.
The humidity control system of temperature and humidity regulating chamber is used to maintain a proper humidity level. When the humidity is too low, the humidity control system releases water vapor to increase the humidity; When the humidity is too high, the humidity control system absorbs the excess humidity to reduce the humidity. With precise humidity control, temperature regulators ensure that the ambient humidity is within the ideal range.
Temperature and humidity regulating chamber is widely used in practical applications. Taking the pharmaceutical industry as an example, some drugs have high requirements for temperature and humidity during processing and storage. If the ambient temperature and humidity are not effectively controlled, the quality and stability of these drugs will be affected. The temperature regulator can provide a stable working environment to ensure the quality and efficiency of the drug.
In the food industry, Temperature and humidity regulating chamber also plays an important role. For example, in the chocolate manufacturing process, the control of temperature and humidity directly affects the texture and taste of chocolate. The temperature regulator accurately controls temperature and humidity, ensuring that the chocolate production process meets standards and produces quality products.
Temperature and humidity regulating chamber is also widely used in electronic, chemical and other industries. In the electronics industry, temperature and humidity control is very important for the production and storage of electronic components. In the chemical industry, some chemical reactions have high requirements for temperature and humidity, which can provide a stable and safe working environment.
High and Low Temperature (& Humidity) Test Chamber (Battery Test Specifications)
Introduction of high and low temperature (& humidity) test chamber (battery test specifications):
High and low temperature (& humidity) test chamber (battery test specifications) mainly provides a constant temperature and high and low temperature alternating test environment for various secondary batteries and fuel cells and other new energy products in the research and development, production, inspection and other aspects of the test. For example: it can be used for lithium battery cells, modules and electric vehicle power; it can also used for lithium battery cells and modules related to energy storage industry.
Features of high and low temperature (& humidity) test chamber (battery test specifications):
Maintaining the advantages of high and low temperature (& humidity) test chamber-P series;
Adding pressure relief valve and observation window protection device to prevent sample explosion from causing injury to people;
Adding gas detection devices to detect flammable, explosive and harmful gases to provide against possible trouble;
Increasing automatic fire extinguishing device in case of fire to reduce losses;
Main parameters of high and low temperature (& humidity) test chamber (battery test specifications):
Studio size: 0.3m ~ 1.5m³(other sizes can be customized)
Temperature range: -40 ℃ ~ +150℃
Humidity range: 20% ~ 98%
Heating rate: 1℃ -5 ℃/min (full time)
Cooling rate: 1℃ -5 ℃/min (full time)
Temperature fluctuation: ±0.5
Temperature uniformity: 2℃
Temperature deviation: ±2℃
Humidity deviation: +2 ~ -3% (> 75%RH), ± 5% (≤ 75%RH)
Vacuum High Temperature Test Chamber
Features of vacuum high temperature test chamber: special high temperature equipment for defoaming and anti-oxidation. And it meets the standards: GB/T2423.1 (IEC60068-2-1), GB/T2423.2 (IEC60068-2-2), ISO16750; JESD22, GB/T 14710, GB/T 13543.
First, product overview of vacuum high temperature test chamber:
New and simple design;
The program of automatic control of pressure and temperature control is easy to operate and advanced in function;
Observation window for easy observation of test material status (optional);
Dual structure in the chamber: the inside of the vacuum container has a dual structure of an inner slot, and a heater is set outside the inner chamber to reduce heat loss, improve temperature uniformity, greatly shorten the temperature rising time, and improve the operating rate of the equipment;
Widely used: can be used for defoaming, degassing, hardening, drying and so on;
Resin liquid mixing and silicone liquid when the defoaming treatment in LED production process, various resin molding degas treatment, IC injection of epoxy resin hardening treatment, drying for electronic parts after water cleaning, vacuum high temperature test chamber can be used in all these process;
Second, different models of vacuum high temperature test chamber:
Model number
Temperature range
Internal volume
Type
Internal size
(W*H*Dmm)
External size
(W*H*Dmm)
VAC-101P
+40～+200℃
91L
Atmospheric pressure range：933～1[*102Pa](abs)
450×450×450
902×1,392×780
VAC-201P
+40～+200℃
216L
Atmospheric pressure range：933～1[*102Pa](abs)
600×600×600
1,052×1,532×930
VAC-301P
+40～+200℃
512L
Atmospheric pressure range：933～1[*102Pa](abs)
800×800×800
1,252×1,772×1,130
Model number
Temperature/pressure range
Internal size
(W*H*Dmm)
LCV-234
(RT+20)°C~+200°C / 0-101kPa(Gauge)
450×450×450
LCV-244
550×550×550
Double 85 Constant Temperature And Humidity Reliability Environmental Test (THB)
First, high temperature and humidity test
WHTOL (Wet High Temperature Operating Life) is a common environmental stress acceleration test, usually 85℃ and 85% relative humidity, which is generally carried out in accordance with the standard IEC 60068-2-67-2019. The test conditions are shown in the chart.
Second, the test principle
"Double 85 test" is one of the reliability environmental tests, mainly used for constant temperature and humidity box, that is, the temperature of the box is set to 85℃, the relative humidity is set to 85%RH conditions, to accelerate the aging of the test product. Although the test process is simple, the test is an important method to evaluate many characteristics of the test product, so it has become an indispensable reliability environmental test condition in various industries.
After aging the product under the condition of 85℃/85%RH, compare the performance changes of the product before and after aging, such as the photoelectric performance parameters of the lamp, the mechanical properties of the material, yellow index, etc., the smaller the difference, the better, so as to test the heat and moisture resistance of the product.
The product may have thermal failure when working in a continuous high temperature environment, and some moisture sensitive devices will fail in a high humidity environment. The dual 85 test can test the thermal stress generated by the product under high humidity and its ability to resist long-term moisture penetration. For example, the frequent failure of various products in the humid weather period in the south is mainly due to the poor temperature and humidity resistance of the products.
3. Experimental factors
In the LED lighting industry, many manufacturers have used the double 85 test results as an important means to judge the quality of lamps. Various possible reasons why LED lamps fail the dual 85 test are:
1. Lamp power supply: poor heat resistance of shell, danger of short circuit in circuit, failure of protection mechanism, etc.
2. Lamp structure: unreasonable design of heat dissipation body, installation problems, materials are not resistant to high temperature.
3. Lamp light source: poor moisture resistance, packaging adhesive aging, high temperature resistance.
If you encounter a special use environment, such as the working environment temperature is severe, you need to test its high and low temperature resistance, the test method can refer to the high and low temperature test project.
4. Serve customers
01. Customer group
LED lighting factory, LED power plant, LED packaging factory
02. Means of detection
Constant temperature and humidity test chamber
03. Reference standards
Constant temperature and humidity tests for electrical and electronic products -- Environmental testing -- Part 2: Test methods -- Test Cab: Constant temperature and humidity test GB/T 2423.3-2006.
04. Service content
4.1 Refer to the standard, conduct double 85 test on the product, and provide the third party's test results report.
4.2 Provide the analysis and improvement plan of the product through the double 85 test.
Get A Quote
IPv6 network supported