ER-135MHP-W, Step in constant temperature and humidity bath, constant temperature and humidity chamber style book (water-cooled)

Project

Type

Form

ER - 135MHP-W

Nature

ability

*1

*2

Temperature and humidity mode

The way of wet ball

Temperature and humidity model * 3

-40~+ 80 ℃ /10~95%RH

Temperature and humidity electrode amplitude

± 0.3 ℃ / ± 2.5%RH

Temperature and humidity distribution

± 0.75 ℃ / ± 5.0%RH

The temperature drops the time

+20~ -40 ℃ Within 170 minutes

Temperature rise time

+20~+ 80 ℃ Within 50 minutes

Noise value

*6

Room outside

65dB

Indoor side

79B

Statutory freezing capacity ( 50 / 60Hz )

2.57/2.81

Product shape-inch method (width, depth and height)

Please refer to the configuration diagram

Warehouse board laboratory

Bed area

13 . 0 m2

The shape of inch method

＊７

Wide

3600mm

Deep

3600mm

High

2325mm

Have oneself

Intensification method

＊７

Wide

3450mm

Deep

3450mm

High

2100mm

External materials

Ivory painted steel plate

Inside the material

Stainless steel plate (SUS304)

Broken heat material

Hard synthetic resin

The weight resistance of the board

5.9 k N/ m2 {600 kgf / m2 }

Door (width and height)

830 mm × 1800 mm Single piece open

Measurement (width and height)

190 mm × 320 mm The door

Indoor light capacity (quantity)

60W( 2 individual )

Cable hole

φ 50 1 (500mm from bed surface height, 1 side)

Controller model and shape method

Wide, deep and high

EU - 6 5MH*2 unit 1200 mm × 710 mm × 1940 mm

External outfit

 Indoor

stainless steel sheet and plate (SUS304)

 Outdoor

L coating color on steel plate; ivory color: color table mark 2.5Y8/2 )

Operate

Steel plate coating color; ivory color: color table mark2.5Y8/2

The oneself can shrink machine

Cooling medium

R404A

Output of freezer 1 (staff)

2.2kW(1) × 2

Cooling and dehumidifier

Multi-channel mixed heat sink type

Condenser (staff number)

Transverse fin type (2) 2

Calorifier

Form

Nickel-chromium heat-resistant alloy heater

Volume

5 . 7kW(3 φ 200V) × 2

Humidifier

Form

SUS 316L Make a surface steam type humidifier

Volume

5 . 4kW(3 φ 200V) × 2

Air supply device

Form (quantity)

Single air supply multi-blade air fan (1)

Survival outside the machine

0　Pa{ 0 mmAq}

Blowing rate

25　(m3 / min )

Back to the uterus

1100( r / min )

Motor form

VTFO-K

Motor output (pole number)

0.75kW(6) × 2

Moisturizing water supply

installation 

The water supply cylinder

Water quality * 8

Electrical conductivity is below 10 μ S / cm

Volume

4L × 2

Feedwater

way

Moisturizing disk

 gravity type

Wet ball Wick disc

Electromagnetic valve type

Controller

The temperature is set

-42.0 ~+ 82.0 ℃

Humidity is set

0~98% RH ( Dry Bulb Temperature 10 ℃ ~ 80 ℃ )

Time setting Fanny

0 ~ 999 Time 59 points (programmed type)0 ~ 20000 Time 59 points (value)

Set decomposition energy

Temperature 0.1 ℃ , humidity 1% RH , time 1 minute

Indicate accuracy

 Temperature  ± 0.8 ℃ ( typ. ), humidity ± 1% RH ( typ. ),  time ± 100 PPM

Vacation type

Value or program

Stage number

20 stage / 1 form

The number of procedures

Number of incoming force (RAM) programs, maximum 32 programs / internal ROM programs, maximum 13 programs

Round-trip number

Maximum of 98 or unlimited

Number of round-trip repeats

Maximum 3 time

Displace the end

JP t 100Ω (a t 0 ℃ ), grade B(JIS C1604-1997 )

control action

When splitting the PID action

Endovirus function

Early delivery function, standby function, setting value maintenance function, power outage protection function,

Power action selection function, maintenance function, transportation round-trip function,

Time delivery function, time signal output function, overrising and overcooling prevention function,

Abnormal representation function, external alarm output function, setting paradigm representation function,

Transport type selection function, the calculation time represents the function, the slot lamp lamp function

Project

Type

Form

ER - 55MHP-W

Temperature control machine

Control panel

Equipment machine

Color LCD operating panel (force contact mode),

Represents the lamp (power supply, transport, abnormal), test material power supply system royal terminal,

External alarm terminal, time signal output terminal, power cord connector,

 Protective device

Warehouse plate test uterine cavity

Test material with

Temperature rise overcooling prevention function (microcomputer: automatic setting)

Temperature rise ter (set: Set above 60℃)

Refrigerating cycle

Overload protection device, high blocking device

Calorifier

Temperature over-rise protection device, temperature fuse

  Humidifier

Air burning prevention device (2 weight), wet plate water level regulator

Blower

Overload protection device

Control panel

Leakage breaker for power supply, fuse (for heater, humidifier),

Fuse (for operating loop), fan reverse prevention relay

In addition to control

Frost system

Defrosting method * 5

Stop cycling defrosting (freezer transport stop),

Heat up defrosting

Cold control

But the system

water

Concondensation control mode (quantity)

Water-making valve for cooling water (2) 2

Repeat

measure

Therstat (operated)

300kg × 2

Electricity

Endyceps sinensis

particular

nature

Source

Communication  three phases　380V　50Hz

Maximum load current

45A × 2

The power supply uses a leakage breaker

60A ( Sensory current 30mA) × 2

Power distribution

Rubber insulation hose 22m m2 × 2

Coarseness of grounding wire

5.5m m2 × 2

cold

step back

water

*9

 Water yield；the yield of water

40L / min (  inlet water temperature  32 ℃ ) × 2

Water pressure

0.1~0.5M Pa{ 1.0~5.0 kgf / cm2 }

 water temperature

18~ 32 ℃

Pipe-inch method

Inlet / exit

PT 1 parent seat / PT 1 parent seat

Humidifying water supply pipe distribution inch method * 8

PT 1 / 2 parent seat

arrange

water

Pipe-inch method

drain-pipe

PT 1 / 2 parent seat

Its

Product products (staff)

 reduce pressure(1) * 8

Wet ball wick (15)

Take instructions (1)